  |
| home > storefront > addtronic cases > 7896-120-90 Hotrod - Bare, with TT-900 |
| 7896-120-90 Hotrod
bare, with TT-900 -- When
Addtronics upgraded these chassis in January of 2000, they
made two significant changes that are of immense benefit
to case geeks: they put a vent at the upper back of
the case, and louvers in the floor under that arcane 5.25
internal mount behind the floppy.
Not only did these two changes improve airflow at that mount, but they allowed us to start building a case that would allow a lot of airflow throughout the whole case: We put a TT-900 in that Upper Back 5.25 HD mount--the Just Cooler / TT-900 'dual exhaust box'. Those fans, venting out the back, allows the use of more and/or higher-speed intake fans . We call these versions the HOTRODS. While coolcases concentrates on developing and building extreme cases that utilitize low- noise fans, we know that many of you already have your own fans and PS--so we're providing a barebones chassis for you. All modifications are completed and a TT-900 is installed--all you have to do is install your own fans and PS. Or, go to the storefront and select the fans you want to install, finish the order, and tell us to set up the case--we'll do the installation for you, as well as give you a package discount. FYI, the 'recommended' version shown further down has a raw flows of about 485 cfm--and we use only Panaflo Low- and Medium Speed Fans to obtain that. |
||
 |
|
|
| CASE: | ||
| 7896-120-90 | ||
| INCLUDED ADDTRONICS ACCESSORIES: | ||
| 5.25>3.5
drive adapter |
||
| CPU fan bracket |
||
| 2
HD hanger |
||
| Addtronisc
parts kit |
(I/O panels, motherboard hardware) | |
| MODIFICATIONS: | ||
| LF: P&D 120 |
(remove lower front factory fan and cage, punch 120, drill mtg. holes) | |
| HD: P&D 120 |
(remove hard drive factory fan cage, punch 120, drill mtg. holes) | |
| DC:
C&D 2 - 92. |
(remove two cages on 5.25 drive column, open fan area, drill two 92 fan mounts | |
| LS-PCI: P&D 120 |
(punch a 120 and drill mtg. holes on the left rear side by PCI slots) | |
| BBd:
P90 |
(remove backboard factory fan mount, punch 90) | |
| APS:
P&D 90 |
(remove Above-PS fan cage, punch 90, drill mounting holes) | |
| UB: louver remov. |
(remove louvers in floor under the Upper Back 5.25 drive mount) | |
| 5
grommet mounts |
(overdrill mtg. holes, install grommets at Lower Front, Hard Drive, Left Side, A-bovePS & Backboard fan mounts) | |
| POWER SUPPLY | ||
| None |
||
| FANS | ||
| credit
memo, factory fans |
(remove the factory fans) | |
| LF: |
none - 120 mm. mount | |
| HD: |
none - 120 mm. mount | |
| DC: |
none - two 92 direct mounts, two factory 80 fan cage mounts | |
| LS-PCI: |
none - 120 mm. mount | |
| BBd: |
none - 92 mm. mount | |
| APS: |
none - 92 mm. mount | |
| UB: TT-900 |
(Just Cooler Bay Cooler/TT-900 --appr. 70 cfm @ 27 dBA) | |
| coolcases.com INCLUDED ACCESSORIES: | ||
| second - 2HD hanger: |
(until 3HD hangers are available again.) | |
| coolcases.com finishing kit | (5.25 'Y' adapter, cable ties in two sizes, cable tie stick-on bases) | |
| SHIPPING: 34 lbs | ||